Table of Contents
Are angle grinders dangerous?
Terry Tuerk, senior product manager—North America at Metabo, West Chester, Pa., uses two analogies to describe just how dangerous it can be to operate an angle grinder. The first compares using an angle grinder to a machine with a knife (the wheel) attached that is moving 220 MPH just inches away from your finger. The second is a person attempting to get out of the way of a Formula 1 car that is only 5 feet away and travelling 220 MPH. Check out Australian General Engineering
In both scenarios, it is humanly impossible to remove yourself from danger (i.e., impact) should something go awry.
Angle grinders are power tools found in just about every metalworking environment. And just like other metalworking equipment, they are dangerous if they are not treated with the care and respect that they command.
Tuerk candidly discusses some of the most common mistakes angle grinder operators make and why those mistakes could be detrimental to their personal safety.
An angle grinder is a tool that needs to be respected. Whether the accessory on that angle grinder is a grinding disc, a cutting disc, or a wire wheel, you have something that is spinning at speeds anywhere from 9,000 to 11,000 RPM, inches from your hands, fingers, body, and face.
We've studied the statistics put out by the Bureau of Labor Statistics (BLS) on injuries, and it's interesting to see that it's generally two groups of people who are being injured while using angle grinders. It's either very young people who are just entering the industry, or it's people who have been in the industry 15 or 20 years.
Injuries in the first group are usually the result of a lack of training, where either they don't know the process, they don't respect the equipment, or they don't understand the safety features that are on the grinders. The second group are the people who insist they have been doing it a certain way for years. I can guarantee you, if you are running an angle grinder for your job without a guard, at some point you are going to be injured by that grinder. That is a fact, 100 per cent.
What makes the angle grinders so dangerous?
An angle grinder is a tool that needs to be respected. Whether the accessory on that angle grinder is a grinding disc, a cutting disc, or a wire wheel, you have something that is spinning at speeds anywhere from 9,000 to 11,000 RPM, inches from your hands, fingers, body, and face.
We've studied the statistics put out by the Bureau of Labor Statistics (BLS) on injuries, and it's interesting to see that it's generally two groups of people who are being injured while using angle grinders. It's either very young people who are just entering the industry, or it's people who have been in the industry 15 or 20 years.
Injuries in the first group are usually the result of a lack of training, where either they don't know the process, they don't respect the equipment, or they don't understand the safety features that are on the grinders. The second group are the people who insist they have been doing it a certain way for years. I can guarantee you, if you are running an angle grinder for your job without a guard, at some point you are going to be injured by that grinder. That is a fact, 100 per cent.
Many of these injuries can be caused by flying abrasive and metallic particles, ejected materials, and from contact with the tool itself. There are several types of accidents caused by angle grinders:
Contact with wheel
Angle grinders can cut through stone, concrete, metal and other strong materials, so they have no trouble cutting through human flesh and bones. Contact with the wheel while in operation can, therefore, have serious consequences.
This is more likely to happen with inadequate guarding. Make sure the safety guard is in place, and wear suitable gloves to keep a good grip during use. Always remain alert and keep concentration during the use of the angle grinder.
Wheel breakage
The risk of breakage is inherent in every abrasive wheel. This risk must be kept low by checking discs, correctly mounting, and safely using angle grinders.
You can stop or reduce the risk of a burst disc by knowing the limitations of the disc you are using. You should only use a disc in good condition, within its expiry date, and within its speed limitations. The maximum speed and expiry date will be marked on the wheel, never exceed these.
Only mount abrasive wheels correctly, and on the tool that they are intended for. Many accidents occur because wheels are mounted in unsuitable or improvised ways, or on tools not designed for that type of disc.
Contact with projectiles
Projectiles can be caused by the wheel bursting (covered in point 2 above) but also by the material being cut or ground.
It's not always possible to prevent projectiles, but you can minimise the risk by using the right tool, wheel and settings for the material. To stop injury, you must wear the correct PPE to protect from the risk of projectiles, especially eye and head protection.
Kickback
Kickback can cause serious and even fatal accidents. This happens when the angle grinder grabs jams on the material when cutting, and is more likely to occur if you are using the wrong wheel, or cutting at the wrong speed.
You can stop this happening by making sure you are using the right wheel for the material, and have set the right speed. Dull and badly set wheels also increase the risk of accidents from kickback. Make sure you are trained in mounting wheels and change your wheels when they become worn.
Kickbacks can cause the user to lose control of the tool, and it can hit the worker or be dropped, causing foot and leg injuries. Always wear PPE including eye, head, foot and hand protection, and suitable clothing.
Always use the right disc at the correct speed.
Entanglement
Wearing the right clothing is important to protect you, but wearing the wrong clothing can also cause an angle grinder accident. As with any rotating disc, there is a risk of entanglement.
Loose clothing such as ties or long baggy sleeves are easily drawn in between the wheel and the workpiece and should not be worn. Long hair should be tied back. Rags and waste should also be removed from the work area, away from the wheel, as they may also become entangled.
Fire
When using an angle grinder, you are likely to produce a large number of sparks. You may not be able to stop this, but you do need to make sure you are in a safe environment for the use of an angle grinder.
For example, if you use an angle grinder near a refuelling station, or close to the storage or use of flammable or explosive substances, you are creating a risk of fire and explosion. If there are flammable materials in the work area, they may catch fire from the flying sparks.
You should always check the work area before using an angle grinder, and remove or protect any combustible or flammable materials.
Electric shock
Many angle grinders are electric, and you should consider accidents caused by portable electrical equipment. Visually check the tool before use, have periodic portable appliance testing, and route cables away from the wheel to avoid contact.
Check out Austgens INDUSTRY SECTORS
Can you describe an unsafe grinding operation you’ve had to deal with?
Several years ago, we manufactured a 5-in. variable-speed grinder, with a range somewhere between 2,000 and 10,000 RPM. Since it's a 5-in, angle grinder, it leaves our factory with a 5-in. guard.
All of a sudden we saw a rash of these tools coming back to us for service—all from one location—each with a 9-in. guard welded around our 5-in. grinder, and the variable speed locked in at around 6,000 RPM. And we were like, "Eh, this is not safe." So we removed the 9-in. guard and replaced it with the standard 5-in. guard. We also fixed the variable-speed dial so that it worked again up to its full range, and then sent them back to the customer. We started getting phone calls from the customer saying, "No, we've done that on purpose, we need our guards back." We told them that as the manufacturer, we could not do that.
We looked further into this and found that they were trying to grind a root weld on a 36-in.-dia. a pipe that had a 6-in.-thick wall. They had to get to the root weld on this pipe and the 5-in. angle grinder could not get down to the root unless it had a 9-in. a wheel on it. This practice ran up through the ranks of the customer and was approved by their international safety people because it was the only way they could get their jobs done. We wouldn't send them back with their guards, but what it led to on our part was the development of the flat-head angle grinder.
Why is it so dangerous to use a wheel that is too big for the grinder?
You greatly increase the possibility of kickback, which is when a wheel binds up or gets caught in the workpiece during operation. The inertia created by the spinning wheel and the mass of the armature inside the motor cause the tool to stop suddenly, creating a situation where the tool wants to kick out of your hands. When this happens, it typically kicks back toward the operator.
What is the primary function of the guard?
Guards are designed to contain a wheel or disc if it shatters or breaks. Specific design standards for the guard require the guard material to be a certain thickness and steel strength to contain a broken wheel. It also must have a locking mechanism so that if it were to shatter, that guard could not open itself automatically to the operator. Most angle grinders have a burst-proof guard.
In the past, you'd have a guard that just clamped onto the grinder with a steel ring and a screw. That's no longer acceptable. You now have to have a locking guard, so we have developed a guard that has seven different locking positions. You can lock it in a cutting position on the right- or left-hand side of the tool, and in many positions in between for grinding as well. But it's locked in that position. If you had an event where the disc shattered, it could not open up toward you.
What are some ways operators customise their tool that might seem harmless but are very unsafe?
The No. 1 thing that we see is taking the guard off the tool. The excuse is that the guard is in the way and people can't see what they're doing. In the past, that may have been true, but today any major manufacturer offers positionable guards. You can change the position of the guard for cutting or grinding to allow you to get into tight areas.
Right behind that is not using the side handle on the angle grinder. Many users say the side handle gets in the way, so the first thing they do when they open the box is to leave the side handle in there, which is a mistake.
Never remove a guard from the angle grinder. Tuerk said guards are designed to contain a wheel or disc if it shatters or breaks.
You should always have two hands on the tool. If you have one hand on the handle located on the back of the grinder and one hand on the side handle, it gives you so much more control than if you were to have two hands on the back of the grinder, like how you would grip a baseball bat.
We've tried to minimise the underuse of the side handle by developing a multi position side handle. Our small grinders still come with a side handle that can mount either to the left or the right side of the grinder. Our large grinders typically have a three-position side handle where you can mount it from the left, right, or on top of the gear housing.
With the multiposition accessory, it's a steel bar that connects to the grinder that allows you to position the side handle anywhere across the top of the grinder on a 180-degree arc from left to right. And it also allows you to position the side handle at 90 degrees to the tool and back toward you at 45 degrees. We've given the operators a reason to keep that side handle on the tool to increase safety. It takes away the excuse that it's in the way.
On many large job sites anymore, not using a guard or a side handle is reason enough for termination. You'll be taken off the job. If it's a union job, you'll be asked to leave. If you're a hired employee, you'll be fired. It's that serious in a lot of cases.
I've even seen people using accessories that are not designed for an angle grinder, for example, a toothed saw blade. Every instruction manual in the industry warns operators not to use a toothed saw blade on an angle grinder, and the reason for that is obvious. Think about it: An abrasive cutting disc can injure you fairly significantly, but a saw blade designed to operate at 3,500 RPM now attached to an angle grinder running at 10,000 RPM? The damage would be a whole lot worse. We've seen it; it's out there. The chances for a kickback on this is multiplied ten times over.
Check out Metal Fabrication Welding Aluminium
What PPE must the operator wear at all times, no exceptions?
You need to wear safety glasses that not only cover the front of the eye but also shield the side of the eye. You need hearing protection. The angle grinder itself might not be loud, but the sound the disc makes on the material greatly amplifies the sounds that are made. You should wear spark-resistant gloves at all times, and I would also suggest wearing a fire-retardant (FR) jacket or clothing. Those safety items are the baseline.
Depending on your application, you may need to wear a full-face shield in addition to safety glasses. If you are working with your face very close to the grinder, the sparks could bounce off the workpiece and come at you.
If you're working inside or in a confined environment like inside of a tank, then you should wear a dust respirator of some sort. You need to be aware of the material that you're working on. If you're grinding stainless steel or if you're grinding on something that could include a leaded component—a wire brush removing leaded paint—then you need to wear a respirator that will protect you from those hazardous bags of dust.
The side handle allows the operator to use two hands during cutting or grinding applications. Placing one hand on the handle located on the back of the grinder and the other hand on the side handle gives the operator more control of the tool. More control equates to more safety.
Are there any characteristics operators should look for in their grinding or cutting wheel before they begin work?
When you remove a disc from the packaging, the first thing you should do is inspect it for any defects. Look for chips, cracks, or anything that looks off. If something looks questionable, dispose of it. Do not mount it on your tool.
After you've inspected and mounted the wheel, run it at no load for at least a minute before you do anything else with that tool. In that time you'll be able to determine if that disc has full integrity. If you're working in a shop environment, make sure you are pointing it away from anyone else. You should run the disc at no load for about a minute any time you change accessories to make sure it doesn't come apart. I don't think many people do this, but it's a recommendation found in angle grinder instruction manuals. It's also found in ANSI B7.1, the regulations for abrasives. It's an end-user standard developed by Unified Abrasives Manufacturers Association (UAMA).
What are some general best practices users should adopt to provide an extra level of safety?
If your angle grinder goes in and out of a tool crib every day, and if that tool crib issues you a grinder with an accessory on it, make sure to let it run no load for a minute. This will allow you an opportunity to inspect the tool and the accessory. Do the same thing if you go on break—you don't know if someone else has picked up that grinder and dropped it.
If you ever drop your angle grinder with an accessory attached, the safest thing to do is assume you've damaged it in some way and change out that accessory. The cost of changing out that cutting or grinding disc pales in comparison to what a potential injury will cost.
Last, the operator is the biggest component in ensuring a safe operation. Never operate the tool under the influence of alcohol or drugs. If you see something unsafe, bring it up to your supervisor or safety person. Don't ignore it. We need to take care of each other.
If you're not feeling 100 per cent, you probably don't want to have a powerful tool in your hand that day. When you get tired—operating these tools is hard work, so it happens—take a break and get away from it for a while. If you find your mind wandering a little bit, get it out of your mind and concentrate on your job.
Remember, an accident with an angle grinder happens before you have time to react.
Check out Exactly what is the sheet metal working procedure?
What are the safety measures in using an angle grinder?
- consider whether an angle grinder is the best tool to perform the task, because another tool may be just as, or even more, effective
- when purchasing a grinder, choose one with adjustable handles that can be moved to suit both lefts. Right-handed operators
- choose a grinder that has an automatic cut-off or dead-man switch as part of the handgrip. This is designed to cut off power as soon as finger pressure is released. Automatic cut-off switches may not be available on smaller models and may not be practicable for certain tasks
- do not use a grinder that is larger, heavier or more powerful than is necessary, as it is much easier to control lighter tool
- guards must not be removed. The guard should cover half of the disc and be positioned between the disc and the operator
- ensure that the correct type of disc is used for the task being performed. The wrong disc could shatter or 'grab' the workpiece causing kickback
- when using a grinder fitted with a cutting disc, keep the depth of cut to no more than double the disc thickness and avoid plunging the disc too far through the workpiece
- provide operators with training and instruction in safe work procedures for angle grinders.
Before use
Before using an angle grinder, ensure that:
- the guard and handles are secure
- there are no defects or damage to the disc (a disc which has been dropped may have developed cracks and should not be used)
- the correct flange and the locking nut is in place for the type of disc being used (otherwise the disc can shatter at high speed)
- the tightening tool supplied by the grinder manufacturer is used to tighten the disc as other methods can damage the disc and grinder
- the correct disc diameter and central disc hole size for the spindle is used
- the correct type of disc is used for example grinding discs for grinding and cutting discs for cutting
- the correct type of disc is used for the material being cut or ground.
During use
Follow these suggested safe practices when an angle grinder is in use:
- use two hands to operate the grinder. One hand should grip the handle and dead-man switch (if provided), while the other hand supports the weight of the tool
- allow the grinder to 'run-up' to operating speed before applying it to the job
- hold the grinder against the workpiece with minimum pressure, so the disc does not 'grab' and cause it to kickback
- never bump the grinder onto the object, or let the disc hit any other object while grinding
- keep the grinding disc at a 15 to 30-degree angle to the object. Ensure the workpiece is held firmly, either as part of a larger item or in a bench vice
- where possible, keep the work at waist height during grinding
- adopt a comfortable stance with feet apart, so you feel well-balanced, and ensure you have a clear view of the job
- never use a grinder between your legs while sitting on the floor
- stop at regular intervals for a short break to rest your hands and arms
- never put a grinder down until the disc stops rotating
- remove the plug from the powerpoint before changing discs
- never use a cutting disc for grinding or a grinding disc for cutting
- when not in use, disconnect the power and place the grinder on a bench with the disc facing upwards.
How to operate an angle grinder?
Operators must be trained under one-on-one supervision in safe practices when using an angle grinder. Two hands should always be used when operating an angle grinder – one to hold the handle and one to support the weight. The angle grinder should be allowed to run up to speed before being applied to the job with minimum pressure so that it doesn't grab and kickback. Grinding discs should be applied at a 15 to 30-degree angle to the object.
Operators should be careful not to let the angle grinder bump against anything, nor should they stand directly behind the tool.
Angle grinders must have stopped turning completely before they are put down or moved around the workplace. Operators should take regular breaks to rest their hands and arms.